Remarks
Ssd1331 | |
---|---|
Status | |
Source code | GitHub |
Datasheet(s) | GitHub |
NuGet package |
The SSD1331 is a display controller used to drive 16bpp (RGB565) color OLED displays over SPI. These displays are commonly found with a resolution of 96x64.
Code Example
MicroGraphics graphics;
public override Task Initialize()
{
Resolver.Log.Info("Initializing ...");
var config = new SpiClockConfiguration(new Meadow.Units.Frequency(12000, Meadow.Units.Frequency.UnitType.Kilohertz),
SpiClockConfiguration.Mode.Mode0);
var spiBus = Device.CreateSpiBus(Device.Pins.SCK, Device.Pins.MOSI, Device.Pins.MISO, config);
Resolver.Log.Info("Create display driver instance");
var display = new St7796s
(
spiBus: spiBus,
resetPin: Device.Pins.D00,
chipSelectPin: Device.Pins.D02,
dcPin: Device.Pins.D01,
width: 320, height: 480
);
graphics = new MicroGraphics(display);
graphics.CurrentFont = new Font8x8();
return base.Initialize();
}
public override Task Run()
{
graphics.Clear();
graphics.DrawTriangle(10, 10, 50, 50, 10, 50, Meadow.Foundation.Color.Red);
graphics.DrawRectangle(20, 15, 40, 20, Meadow.Foundation.Color.Yellow, false);
graphics.DrawText(5, 5, "Meadow F7");
graphics.Show();
return base.Run();
}
Sample project(s) available on GitHub
Wiring Example
To wire a Ssd1331 to your Meadow board, connect the following:
Ssd1331 | Meadow Pin |
---|---|
LED- | 3V3 |
LED+ | GND |
MOSI | MOSI |
SCK | SCK |
RESET | D15 |
A0 | D14 |
CS | D13 |
VCC | 3V3 |
GND | GND |
It should look like the following diagram:
Syntax
public class Ssd1331 : TftSpiBase, IGraphicsDisplay
Constructors
Ssd1331(ISpiBus, IDigitalOutputPort, IDigitalOutputPort, IDigitalOutputPort, Int32, Int32)
Create a new Ssd1331 color display object
Declaration
public Ssd1331(ISpiBus spiBus, IDigitalOutputPort chipSelectPort, IDigitalOutputPort dataCommandPort, IDigitalOutputPort resetPort, int width = 96, int height = 64)
Parameters
Type | Name | Description |
---|---|---|
ISpiBus | spiBus | SPI bus connected to display |
IDigitalOutputPort | chipSelectPort | Chip select output port |
IDigitalOutputPort | dataCommandPort | Data command output port |
IDigitalOutputPort | resetPort | Reset output port |
System.Int32 | width | Width of display in pixels |
System.Int32 | height | Height of display in pixels |
Ssd1331(ISpiBus, IPin, IPin, IPin, Int32, Int32)
Create a new Ssd1331 color display object
Declaration
public Ssd1331(ISpiBus spiBus, IPin chipSelectPin, IPin dcPin, IPin resetPin, int width = 96, int height = 64)
Parameters
Type | Name | Description |
---|---|---|
ISpiBus | spiBus | SPI bus connected to display |
IPin | chipSelectPin | Chip select pin |
IPin | dcPin | Data command pin |
IPin | resetPin | Reset pin |
System.Int32 | width | Width of display in pixels |
System.Int32 | height | Height of display in pixels |
Properties
DefautColorMode
The default display color mode
Declaration
public override ColorMode DefautColorMode { get; }
Property Value
Type | Description |
---|---|
ColorMode |
Overrides
SupportedColorModes
The color modes supported by the display
Declaration
public override ColorMode SupportedColorModes { get; }
Property Value
Type | Description |
---|---|
ColorMode |
Overrides
Methods
Initialize()
Initalize the display
Declaration
protected override void Initialize()
Overrides
SetAddressWindow(Int32, Int32, Int32, Int32)
Set addrees window for display updates
Declaration
protected override void SetAddressWindow(int x0, int y0, int x1, int y1)
Parameters
Type | Name | Description |
---|---|---|
System.Int32 | x0 | X start in pixels |
System.Int32 | y0 | Y start in pixels |
System.Int32 | x1 | X end in pixels |
System.Int32 | y1 | Y end in pixels |